Technical specifications | Fluid services
1. Water and Gas Taps
- Built with a pipe that is coated with plastic Rilsan, in compliance with the ASTMB-117, AFNOR B-117 and AFNORX 41-002 Standards or equivalent European standards. They have been designed with a lock that employs 2 ceramic pads (aluminium oxide).
- Gas taps have a safety lock.
- Each tap is identified by the colour of its lever, in compliance with the DIN 12920 Standard.
2. Polypropylene Sink
- Sink with tap heads and perimeter edge, in compliance with DIN 12916, 40x40x25 cm central basin and self-supporting board with a 20 mm thickness.
3. Stainless Steel Sink
- Sink manufactured with 18/10 AISI 304 stainless steel.
- Drain with 11/2” valve and shutoff plug.
- Special sealing tape.
4. Electricity
ELECTRICAL CONDUIT
- Built with 110 x 60 PVC.
- This conduit can be used to add or remove AC/DC sockets of different potential and line selection easily; halogen-free
cabling.
- It complies with the DIN 50085-2-1; DIN UE 0604 - P1 -P2; DIN UE 0606 - P1 Standards.
ELECTRICAL TOWERS
- Built with die cast aluminium and Rilsan coating, with insulating plastic casing. 2 or 4 SCHUKO bases for centre or wall mounted benches.
EMERGENCY SHOWERS
- The Emergency Shower has large diameter showers (250 mm), built in ABS, an anti-corrosive plastic, with a high-visibility yellow colour; large water flow rate and do not become plugged by dirt or lime, since the shower’s holes are small, and a circular water curtain.
EYE WASHING BASING
- Eye washing basins with one or two sprinkles and yellow ABS basin provide a large flow of pressurised water, which bathes the person’s face and eyes, preventing damage to eye tissues.
- Eye washing basins have a built-in dust cover with an automatic operation that is activated when the sprinkler is used.
5. Gas Extraction Cabinets, mod. KV- 1800
- Dimensions: 1.80 m (length) X 0.92 m (width) X 2.65 m (height)
- Composed of the following elements:
TOP BODY
- Interior body, built with Fireproof high-pressure Resin (complies with the new European regulations), classified higher than the former M1.
- Maximum resistance to fire.
- 1 U-profile metallic structure, 50x30x1.5 mm ST 34.
- 1 Double hung window built with profiles, with two 3+3 mm high safety sliding laminated glass doors on 10 mm compact
Stratified guide rails.
- Built with a safety counterweight on the rear section that prevents the double hung window from being accidentally
dropped, with double steel cable and opening on the rear.
- All metallic elements of the fume hood have been treated with an epoxy coating.
- Two top accessible doors and side doors with melamine board, intermediate fiber density and 2 mm PVC edges.
- Jointless acid-proof stoneware worktop, with a 30 mm thick spill-proof edge, clear grey colour.
- Top condensed gas evacuation device.
LOWER BODY
- Front service panel for remote control, electrical bases and electrical protection elements.
- Installed in a vertical position.
- Design for ease of access to installations.
SERVICES
- 0.37 Hp Polypropylene extractor at 1,360 r.p.m. Flow rate: 2,300 m / 3 h.
- Control board.
- Speed variator.
- Fire detector.
- Stoneware basin, 240x 90 mm.
- Gas tap, with remote control.
- Water tap, with remote control.
- Three 10/16 Legrand electrical sockets.
ELECTRICAL PROTECTION ELEMENTS
- Earth leakage protection, circuit breaker and motor protection relays.
- erior lighting with fluorescent lamp > 500 lux.
- Flashing light.
- Modular 2P 20A switch with red LED.
FIRE PROTECTION SYSTEMS
- Extraction speed safety with fire protection system with built-in rate-of-rise detector.
- Maximum opening device, in compliance with the UNE- EN 14175 Standard.
6. Bench for Weighing Scales
- Metallic structure built in steel 60 x 30 x 1.5 mm, in compliance with the standard (DIN 17.100). This structure will have an epoxy finish.
- It has an anti-vibration Granite plate, 45 x 45 cm, on anti-vibration Silentblocks.
7. Armchairs & Stools for Laboratories
- TELIPO Series: Ergonomic chair, High Backrest, Permanent contact, with wheels, gas-elevation system. Interior wooden seat. Upholstered in Imitation Leather, Aran.
- INFOR 60 Series: Intermediate backrest. Permanent contact. Gas-elevation system. Polypropylene Casing of the seat and backrest. Ergonomic design. Polyamide base with wheels. Upholstered in Imitation Leather, Aran.
- INFOR 60-B Series: Intermediate backrest. Permanent contact. Gas-elevation system. Polypropylene Casing of the seat and backrest. Ergonomic design. With armrests. Polyamide base with wheels. Upholstered in Imitation Leather, Aran.
- INFOR 61 Series: High backrest. Permanent contact. Gas-elevation system. Polypropylene Casing of the seat and backrest. Ergonomic design. Polyamide base with wheels. Upholstered in Imitation Leather, Aran.
- INFOR 61-B Series: High backrest. Permanent contact. Gas-elevation system. Polypropylene Casing of the seat and
backrest. Ergonomic design. With armrests. Polyamide base with wheels. Upholstered in Imitation Leather, Aran.
- INFOR 60-AR Series: Intermediate backrest. With footrest ring. Permanent contact. Gas-elevation system. Polypropylene Casing of the seat and backrest. Ergonomic design. Optional fixed armrests. Polyamide base with wheels. Upholstered in Imitation Leather, Aran.
8. Stools for Laboratories
- ZEUS Series: Five-leg stool with 22 mm diameter steel tube, white epoxy finish with chrome plated footrest ring. Rotating and height-adjustable with a spindle. Upholstered with polypropylene, imitation leather, varnished beech wood.
- NO 10 Series: Five-leg stool with polypropylene legs, chromed steel tube, chromed plated footrest and adjustable height. Polypropylene seat and backrest. Lift/gas-elevation system.
